Edge flashing
Drip edge is added where the roof edge had none which stops the rot from coming back.
Exterior Services
Fascia Repair Bloomingdale, NJ
A roofer in Bloomingdale can repair or replace rotted fascia boards, reattach sagging gutters and fix the drip edge that keeps water off the wood, so the gutters have solid wood to hang from again. Dial (862) 356-0010 to talk with a local roofer about the fascia.
The fascia sits right where water leaves the roof, so it is the first trim board to rot when that water goes the wrong way. Clogged or poorly pitched gutters spill over the back, and a roof edge with no drip edge sends water straight down the fascia. Once the wood is soft, gutter hangers pull loose and the gutter sags or tips forward.
Rotted fascia is often the visible part of a bigger problem. The same water rots the ends of the rafters, the first course of roof decking and the soffit nailer. On homes with metal fascia wrap, the rot often goes unseen until the gutter falls.
Before the visit, take a look along the roof edge from the ground. Write down which sides of the house show peeling paint, gaps or a sagging gutter. Mention whether the fascia is painted wood, PVC or covered in aluminum, and how old the gutters are.
Fascia Repair is often paired with soffit repair and gutter installation, depending on the cause.
Looking for Bloomingdale fascia repair? Call (862) 356-0010 and describe the problem to a roofer who works in Bloomingdale.
Call nowThe process
What happens during a fascia repair
A fascia repair only lasts if the water that rotted it is redirected.
Check the edge
Before the board comes off, the roofer looks at what has been soaking it, from the shingle edge to the downspout. The length of the damage decides how much board is replaced.
Remove the gutter
Gutters are taken down along the damaged stretch, which also shows how well the hangers were holding. This is a good time to check the gutter itself for leaks and bad seams.
Inspect behind the board
The roofer looks at the rafter ends and the sub-fascia, since soft framing will not hold a new board. New fascia nailed to rotten rafter ends will loosen again.
Fit the board
New fascia in primed wood, PVC or composite is cut to fit, with scarf joints at the seams. Wood is primed on every side, including cut ends, before it goes up.
Reset the drip edge
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. Without it, the same board will rot again.
Reattach gutters
Gutters are rehung on the new fascia with a slight slope toward the outlets. Wood fascia gets a finish coat of paint.
What is included
What fascia repair covers
Framing repair
Soft framing at the roof edge is reinforced before the fascia goes back on.
Rotted board repair
Rotted sections of fascia are cut out and replaced with new boards and scarfed into the existing board.
Gutter rehanging
Loose gutters are refastened and pitched toward downspouts at the right slope.
Fascia wrapping
Metal wrap can be added over new or sound fascia once any rot is gone.
Related service
Fascia Board Replacement Bloomingdale, NJ
Full fascia board replacement is the right call when soft spots keep turning up along the same edge or when old boards are cracked throughout. The gutters come down, the old boards come off and the rafter tails behind them are checked before new boards go up. Many homeowners switch to PVC or composite fascia at this point because it will not rot.
In Bloomingdale, fascia board replacement often lines up with a new roof or new gutters, since the roof edge is already being worked on. Make sure rotted boards are removed, not covered. The new boards should match the old width so the soffit closes properly.
Related service
Fascia Board Repair Bloomingdale, NJ
When rot is confined to short stretches, the damaged part of the board can be cut out and a new piece scarfed in. The new piece is joined with an angled scarf joint so the seam is strong and less likely to open. For a shallow soft spot, an epoxy consolidant and filler can restore the surface without cutting the board.
Patching a fascia board in Bloomingdale without fixing the gutter or drip edge above it just buys a season or two. Common fixes include a resealed gutter joint, a cleared outlet or a new length of drip edge. Once the wood is primed and painted on all sides, a repaired section can last as long as the rest of the board.
Local help
Fascia Repair Near Me
In Bloomingdale, fascia tends to fail first on the sides of the house where gutters clog fastest. Across Bloomingdale and nearby communities including Wanaque, Butler, Riverdale and Pompton Lakes, the fascia under trees and heavy gutter loads is the first to go, which is why keeping gutters clear does so much to protect the fascia.
Searching for fascia repair near me from Bloomingdale or Wanaque, Butler, Riverdale and Pompton Lakes? Call (862) 356-0010 to talk to a roofer who works in your part of town.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Bloomingdale is busiest after a hard winter and before the next one.
Why call
Why fix it now
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local knowledge
Roofers in Bloomingdale know the roof types and weather wear common in local homes.
Straight answers
Ask your questions before you agree to anything.
Fascia Repair questions
Should I cover rotted fascia with metal?
Metal wrap only belongs over sound wood. Gutter screws go through the wrap into the rotting board and gradually pull loose. Replace the rotted board first, then wrap it if you want low upkeep.
Which fascia material lasts longest?
Rot-proof materials such as PVC and composite last longest. Primed wood is easy to match on older homes but needs regular paint. No material holds up if water keeps running behind the gutter.
Why is my fascia rotting?
Most fascia rot traces back to the roof edge and the gutters. A missing drip edge, clogged gutters and leaking gutter seams all keep the wood wet after every rain. Bare end grain and failed paint let water soak in faster.
Do fascia boards affect my gutters?
A gutter is only as secure as the board behind it. Soft fascia lets the fasteners work loose, which is often the first sign of rot. Repairing the fascia and rehanging the gutter with hidden hangers fixes both problems at once.
Do I need new fascia boards or just a repair?
Repair is fine when damage is limited to a few spots and the rafter tails are sound. When rot runs along most of a wall or the boards are split throughout, full replacement makes more sense. Either way, the rafter tails behind the board need to be checked.
More questions? Call (862) 356-0010
Often needed together
Soffit Repair
Fixing damaged soffits, blocked soffit vents and gaps where animals get in, matched to what is causing the damage in the first place.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Gutter repair for leaking seams, sagging runs, loose hangers and broken downspouts, without replacing gutters that still have life in them.
Learn moreRoof Repair
Targeted roof repairs for wind, age and water damage, matched to what is actually wrong up top.
Learn more
Looking for something else?
See all roofing servicesNeed fascia repair in Bloomingdale, NJ?
Call now for Bloomingdale fascia repair and help in the towns around it.