Tile attachment
Tile is fastened with nails, screws, clips or adhesive in a pattern set by the tile profile.
Tile Roofing
Tile Roof Installation Bloomingdale, NJ
A Bloomingdale tile roofer can help choose between clay and concrete, flat or curved profiles, and install the full system beneath the tile. One call to (862) 356-0010 reaches a nearby tile installer.
Tile is one of the heaviest roofing materials a house can carry, so a tile roof installation starts below the roof. A tile roof weighs several times as much as asphalt shingles, and a home built for shingles may need an engineer to check the rafters or trusses before switching. Houses designed for tile already account for that load in their framing.
The tile choice comes next. Clay holds its color through the whole tile and lasts for generations, and concrete tile is heavier, more absorbent and offers a wide range of shapes and finishes. The profile can be flat, low curve or high curve, and each handles water and wind a little differently.
The tile may last generations, but the layers below it decide when the roof leaks. Codes typically allow tile on slopes down to 2.5 in 12, with two layers of underlayment required on slopes under 4 in 12. Choosing a long lasting underlayment now is what keeps the roof from needing a relay in twenty years.
Many tile roof installation calls in Bloomingdale also turn up a need for tile roof replacement or roof installation.
Looking for Bloomingdale tile roof installation? Call (862) 356-0010 to talk to a local roofer.
Call nowThe process
What happens during a tile roof installation
A tile roof goes on in layers, and the tile is the last of them.
Check the structure
The roofer confirms the framing can carry the tile, often with an engineer when a home is switching from shingles, and pulls the permit the job needs. Tile is ordered with extra for cuts, hips and future repairs.
Dry in the roof
Solid sheathing is inspected and renailed, then the roof is dried in with underlayment, doubled where the slope calls for it. The underlayment is the true waterproof layer, so this step deserves the most care.
Set the battens
Battens are fastened across the roof at spacing set by the tile, and on many roofs counter battens run beneath them so water can drain freely. Some systems skip battens and fasten tile directly, depending on the profile and the slope.
Flash the details
Valley metal, wall and headwall flashing, chimney flashing and soft metal flashing for vent pipes go in before and during tiling. Because tile is thick and curved, flashing must be wider and shaped to fit.
Set the field tile
Tile goes on from the eave up, with an eave closure to keep birds out and fasteners or foam adhesive chosen for local wind requirements. Cut edges at valleys and hips are fitted and secured carefully.
Finish the ridge
Hips and ridges are capped, often with a mechanically fastened system that allows ridge ventilation. The roof is cleaned, broken pieces are replaced and spares are left with the owner.
What is included
Parts of a tile roof installation
Waterproof layer
Doubled or self-adhered underlayment goes down where needed as the real barrier against water.
Load check
Rafters or trusses are confirmed before tile is ordered and reinforced where needed.
Ridge finish
The first course gets an eave closure and the ridge gets capped with ventilation where the design calls for it.
Valley metal
Wide valley metal and shaped wall flashings are installed so water stays on top of the underlayment.
Related service
Barrel Tile Roof Installation Bloomingdale, NJ
Barrel tile is the classic two-piece tile roof: half-round pan tiles laid concave side up, with cover tiles laid over the joints between them. Each tapered tile overlaps the one below it, and the deep shape throws the strong shadow lines that give the roof its look. Because of that depth, barrel tile needs careful work at the eaves, hips and ridges, where the open curves must be closed off.
For barrel tile installation on a Bloomingdale home, each cover tile is secured with nails, wire ties, clips or foam adhesive, depending on the slope and wind rules. Straight, evenly spaced rows take chalk lines and patience on the deck.
Related service
Spanish Tile Roof Installation Bloomingdale, NJ
Spanish tile, also called S tile, merges the curved pan and cover into one interlocking piece. Clay and concrete Spanish tile are both common, in solid and blended colors. Side interlocks help it shed water, though the curved ends need bird stops and ridge closures just like barrel tile.
For Spanish tile roof installation in Bloomingdale, the underlayment and flashing matter as much as the look of the tile. The curves make flashing tricky, so roofers use shaped metal or flexible flashing that conforms to the tile. If you choose a blend, the roofer mixes tile from several pallets at once to spread the color evenly.
Local help
Tile Roof Installation Near Me
In Bloomingdale, new tile roofs go onto homes of every age, from fresh builds to older houses moving away from shingles. In Bloomingdale and neighboring communities including Wanaque, Butler, Riverdale and Pompton Lakes, the biggest variable on a conversion is whether the existing framing can carry tile, and storms that bring strong wind make fastening choices as important as the tile itself.
Searching for tile roof installation near me from Bloomingdale or Wanaque, Butler, Riverdale and Pompton Lakes? Call (862) 356-0010 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Bloomingdale
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Bloomingdale is busiest after a hard winter and before the next one.
Why call
Why fix it now
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Bloomingdale
Roofers in Bloomingdale know the roof types and weather wear common in local homes.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Tile Roof Installation questions
Can tile go over old shingles?
A tile roof needs a bare deck, so existing shingles or other roofing are removed. Removing the old roof also takes weight off the framing, which matters with a material this heavy.
What underlayment goes under a tile roof?
Tile roofs use heavy felt, synthetic underlayment or self-adhered membrane, sometimes in two layers. The underlayment usually wears out long before the tile, so a durable one delays the first relay. Codes call for two layers on slopes from 2.5 in 12 up to 4 in 12.
Can my house hold a tile roof?
Tile weighs several times as much as asphalt shingles, with concrete tile usually the heaviest. Homes built for tile carry it fine, but a house framed for shingles may need an engineer to check the rafters or trusses and add reinforcement. Some lighter weight tile products are made for homes with less structural capacity.
Should I choose clay or concrete roof tile?
Each has real strengths. Clay tile resists fading and has lasted a century or more on some older buildings. Concrete is sturdy and widely available, though it absorbs more moisture and its surface weathers with age.
How long does it take to put on a tile roof?
A typical home takes longer than a shingle roof, often one to a few weeks depending on size, complexity and weather. Complex rooflines and framing work before tiling can stretch the schedule. The roof is dried in with underlayment early, so the house is protected while tiling continues.
More questions? Call (862) 356-0010
Often needed together
Tile Roof Replacement
Replacing a worn tile roof, either by relaying the existing tile over new underlayment or by switching to new tile, so the layers under the tile last as long as the tile.
Learn moreRoof Installation
New roof installation done in the right order with the right details, so it sheds water at every edge and seam.
Learn moreTile Roof Inspection
A close look at the tile, underlayment, flashing, valleys and attic of a clay or concrete tile roof, without breaking tile in the process.
Learn moreRoof Ventilation
Roof ventilation work that keeps the attic dry in winter and cooler in summer, without mixing vent types that work against each other.
Learn more
Looking for something else?
See all roofing servicesGet tile roof installation help in Bloomingdale
Call (862) 356-0010 to talk to a roofer serving Bloomingdale, NJ.