AC curb repair
Vents, skylights and the AC curb are resealed with a sealant that suits the roof.
A roofer in Bloomingdale can repair a mobile home roof by resealing open seams, replacing loose fasteners, sealing vents and the AC curb and recoating the roof so it sheds water again. Dial (862) 356-0010 to talk through the leak with a local roofer.
Leaks on a manufactured home roof tend to follow a predictable pattern. Older single and double wides often have galvanized steel or aluminum roofs on bowed trusses, and newer manufactured homes may have rubber membrane or shingles. For metal roofs, panel seams, fastener holes and dried sealant at vents and the perimeter edge cause most leaks.
Water does damage quickly in a manufactured home. Thin ceiling panels stain and bow, insulation gets soaked and the wood framing can start to rot before the leak is obvious. If a ceiling panel bulges with trapped water, a small hole at the low point lets it drain into a bucket, keeping clear of light fixtures, and power to that area should be shut off at the panel if it is safe to reach.
Mobile home roofs are not built to be walked on like a house roof. Weight should go on the trusses, not between them, which is why roofers often use boards to spread their weight. Stay off a wet or icy roof, and look for the data plate inside the home, which shows the roof load the home was designed for.
Mobile Home Roof Repair is often paired with roof coating and metal roof repair, depending on the cause.
Dealing with this in Bloomingdale, NJ right now? Call (862) 356-0010 and describe the problem to a roofer who works in Bloomingdale.
Call nowHere is how a roofer usually approaches a mobile home roof repair.
The roofer walks the truss lines or works from a ladder, checking seams, fasteners, the perimeter edge and every vent, skylight and curb. Stains on the ceiling inside help narrow down the source.
Missing or loose screws are replaced and panels are secured so the roof stops rumbling. Rusted spots are cleaned and treated before sealing.
Panel seams are cleaned and sealed with butyl seam tape or a reinforced seam sealer. Membrane roofs get matching patches and seam repairs instead.
Every roof penetration is resealed, with brittle vent caps or skylight domes replaced. The edge rail around the roof is resealed too.
On metal and some membrane roofs, a full elastomeric or silicone roof coating is applied after repairs to seal small gaps and reflect sun. Coatings need dry weather and a clean surface to bond.
Vents, skylights and the AC curb are resealed with a sealant that suits the roof.
Panels are secured with new screws to close leaks at every screw.
Water damaged areas are opened and fixed so the roof is solid again.
The roof is recoated after repairs to seal and protect it.
Panel joints are cleaned and resealed to stop drips into the ceiling.
When repairs cannot keep up, a mobile home roof replacement removes the old roofing and installs a new system. Depending on the home, the new roof may be metal, a single ply membrane such as EPDM or TPO, or shingles on a pitched roof. Rotted trusses are repaired or reinforced before the new roof goes on.
For mobile home roof replacement in Bloomingdale, the roofer has to plan around light framing and the roof load the home was built for. A permit may be required, and rules for manufactured homes can differ from site-built homes, so the roofer should check local requirements. Done right, the new roof should end the cycle of patching.
Rather than removing the old metal, a roof over adds a new roof system above it. Options include a framed pitched roof that adds an attic space, an insulated membrane roof over, or new metal fastened over furring strips. Many roof overs add insulation, cutting heat gain and making the home quieter in storms.
For a Bloomingdale mobile home roof over, the roofer checks the walls and trusses, since the new roof adds weight and catches more wind. A pitched roof over changes the structure, so it often needs a permit and engineering, plus solid anchoring for wind. A good roof over ends the seam and screw leaks that plague old metal roofs.
Around Bloomingdale, mobile home roofs include older metal roofs, rubber membrane roofs and newer shingle roofs on pitched manufactured homes. For homes in Bloomingdale and nearby towns like Wanaque, Butler, Riverdale and Pompton Lakes, resealing and recoating every several years keeps most metal roofs dry, and catching a leak early keeps ceiling panels and framing from rotting.
Need mobile home roof repair around Bloomingdale? Call (862) 356-0010 for a Bloomingdale roofer who serves the towns around it too.
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Bloomingdale, NJ have the roof checked in the fall and again after the snow melts.
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local roofers see the same roofs and storm damage across Bloomingdale and nearby towns.
Ask your questions before you agree to anything.
More questions? Call (862) 356-0010
A seamless coating over a sound but weathered roof, after the seams and blisters are repaired.
Learn moreRepairs for leaking fasteners, open seams, rusted panels and failed flashing on a metal roof, so the panels keep shedding water for years more.
Learn moreFixing open seams, punctures, shrinkage and split flashing on EPDM rubber roofs, never with tar or asphalt cement that ruins the rubber.
Learn moreFinding where water gets through the roof and sealing it at the source, with the damage underneath checked too.
Learn moreLooking for something else?
See all roofing servicesCall (862) 356-0010 to talk to a roofer serving Bloomingdale, NJ.